dev March 2017

dev@openadk.org

3 participants
18 discussions

BruteFIR performance test
by lich000king＠yahoo.de 21 Mar '17

21 Mar '17

Hi Well, thanks to wbx, brutefir runs again! :-)I reran the performance test on my core2duo machine on an asus-p5bvm in adk with kernel 4.4.50-1.For the 30:00 test file it now takes 18 seconds!This is a 40% performance increase compared to earlier runs using adk on the same machine! :-)Also, this is now the same runtime I had on this machine running lfs with kernel 3.10.10.It is encouraging to now get the same runtime.Though I do not know where the performance boost comes from. Does anyone have an idea? The next step will be to rerun the test on the pi2, to see if it runs faster there as well. CheersOliver ----- Weitergeleitete Message ----- Von: "lich000king(a)yahoo.de" <lich000king(a)yahoo.de> An: "dev(a)openadk.org" <dev(a)openadk.org> Gesendet: 21:09 Mittwoch, 2.Dezember 2015 Betreff: BruteFIR performance test Hi there So, I have also run the test on my Hummingboard i2ex. Here it takes around 4.5 minutes, i.e. almost 50% longer than on the pi 2.On the core2duo machine I have also repeated the test in adk. It takes around 30 seconds, more than 50% longer than on the same machine running lfs (linux 3.10.10). This may well be due to a not optimized kernel config. I will need to delve deeper into this to find out. Any ideas and comments are welcome:-) CheersOliver ----- Weitergeleitete Message ----- Von: lich000king <lich000king(a)yahoo.de> An: dev(a)openadk.org Gesendet: 20:47 Dienstag, 27.Oktober 2015 Betreff: BruteFIR performance test Hi again Performed the same test on my core2duo machine (approx. 10 years old). It takes around 18 seconds. So it is roughly 10x faster. Does this sound reasonable or should I expect better performance from the raspberry pi 2? The test is designed to use two cores only. I have not managed setting up OpenADK on this machine yet, so this test ran on lfs (linux 3.10.10-rt7). But this should not affect the results much. I also tried to run the test on the hummingboard. But there BruteFIR gives me an error which I don't quite understand: BruteFIR v1.0m (November 2013) (c) Anders Torger Internal resolution is 32 bit floating point. Creating 4 FFTW plans of size 8192...finished. Loading coefficient set...finished. Failed to open module "file" in "/usr/lib/brutefir/file.bfio": /usr/lib/brutefir/file.bfio: undefined symbol: __aeabi_idivmod. It looks like a problem with a floating point operation. If anyone has any insight to any of these it will be much appreciated. :-) Cheers Oliver On 18.10.2015 14:58, lich000king wrote: Hi everyone I am still wondering if it is possible to improve brutefir performance on arm. In order to assess the convolution performance, I have prepared a little test procedure. So here is how to test BruteFIR performance on OpenADK: I used adk revision 463aa3b 2015-10-14 | update firmware and kernel to latest. In order to perform this test you have to build adk with brutefir and sox packages (for now better don't enable PREEMPT_RT_FULL as there is an unresolved conflict with the bcm driver). In adk do the following: ********************************************************************************** rw mkdir /root/bftest cd /root/bftest cat > /root/bftest/wavtest.conf << "EOF" # Begin /root/bftest/wavtest.conf # File used for testing brutefir # Uses dirac pulse als filter. # Stereo only. Input from file /root/bftest/pinknoise.wav. Output to file /root/bftest/output.wav. ## DEFAULT GENERAL SETTINGS ## float_bits: 32; # internal floating point precision sampling_rate: 44100; # sampling rate in Hz of audio interfaces filter_length: 4096,16; # length of filters # config_file: "/home/audiovero/.brutefir_config"; # standard location of main config file overflow_warnings: true; # echo warnings to stderr if overflow occurs show_progress: false; # echo filtering progress to stderr max_dither_table_size: 0; # maximum size in bytes of precalculated dither allow_poll_mode: false; # allow use of input poll mode modules_path: "/usr/lib/brutefir"; # extra path where to find BruteFIR modules monitor_rate: true; # monitor sample rate powersave: -80; # pause filtering when input is zero lock_memory: false; # try to lock memory if realtime prio is set convolver_config: "/root/bftest/brutefir_convolver"; # location of convolver config file #benchmark: true; ## LOGIC ## logic: "cli" { port: 3000; }; ## COEFFS ## coeff "dirac" { filename: "dirac pulse"; format: "FLOAT64_LE"; }; ## INPUT, OUTPUT ## input "fleft", "fright" { device: "file" { path: "/root/bftest/pinknoise.wav"; skip: 44;}; # ignore_xrun: true; }; sample: "S16_LE"; channels: 2/0,1; }; output "fr", "fl" { # device: "alsa" { device: "hw:0";}; # ignore_xrun: true; }; device: "file" { path: "/root/bftest/output.wav"; }; sample: "S16_LE"; channels: 2/0,1; dither: true; }; ## FILTERS ## filter "frfilter" { from_inputs: "fright"; to_outputs: "fr"; coeff: "dirac"; }; filter "flfilter" { from_inputs: "fleft"; to_outputs: "fl"; coeff: "dirac"; }; # End /root/bftest/wavtest.conf EOF # generate 30 minutes of pink noise as test input for brutefir sox -t sl -r 44100 -c 2 /dev/zero -r 44100 -c 2 -b 16 pinknoise.wav synth 30:00 pinknoise vol 0.6 # run brutefir once in order to generate fftw plans (you can cancel this as soon as you see the "Audio processing starts now..."): brutefir -nodefault /root/bftest/wavtest.conf # Then measure the time it takes to convolve this test file by doing: time brutefir -nodefault /root/bftest/wavtest.conf ********************************************************************************** The first test will not give the correct time since it has to generate FFWT plans which takes quite some time. So you can cancel it the first time as soon as you see the "Audio processing starts now..." and restart it. The second time it will start convolving immediately. On my rpi2 it takes approx. 3 m 10 s to 3 m 20 s. The question now is if there is a way to improve brutefir performance on arm, possibly by using some hand coded assembler. Happy testing and thanks for any feedback! All the best Oliver

1 0

segfault in brutefir
by lich000king 18 Mar '17

18 Mar '17

Hi After a break, I am trying to catch up on the brutefir performance test in adk. Unfortunately, with the current revision of adk (2af0538) I get a segmentation fault when running brutefir in offline mode. It can be reproduced by building qemu with brutefir and sox and then doing: cd /etc/ mkdir bftest cd bftest sox -t sl -r 44100 -c 2 /dev/zero -r 44100 -c 2 -b 16 pinknoise.wav synth 1:00 pinknoise vol 0.6 cat > wavtest.conf << "EOF" # Begin wavtest.conf # File used for testing brutefir # Uses dirac pulse als filter. # Stereo only. Input from file pinknoise.wav. Output to file output.wav. ## DEFAULT GENERAL SETTINGS ## float_bits: 32; # internal floating point precision sampling_rate: 44100; # sampling rate in Hz of audio interfaces filter_length: 4096,16; # length of filters # config_file: "/home/audiovero/.brutefir_config"; # standard location of main config file overflow_warnings: true; # echo warnings to stderr if overflow occurs show_progress: false; # echo filtering progress to stderr max_dither_table_size: 0; # maximum size in bytes of precalculated dither allow_poll_mode: false; # allow use of input poll mode modules_path: "/usr/lib/brutefir"; # extra path where to find BruteFIR modules monitor_rate: true; # monitor sample rate powersave: -80; # pause filtering when input is zero lock_memory: false; # try to lock memory if realtime prio is set convolver_config: "brutefir_convolver"; # location of convolver config file #benchmark: true; ## LOGIC ## logic: "cli" { port: 3000; }; ## COEFFS ## coeff "dirac" { filename: "dirac pulse"; format: "FLOAT64_LE"; }; ## INPUT, OUTPUT ## input "fleft", "fright" { device: "file" { path: "pinknoise.wav"; skip: 44;}; # ignore_xrun: true; }; sample: "S16_LE"; channels: 2/0,1; }; output "fr", "fl" { # device: "alsa" { device: "hw:0";}; # ignore_xrun: true; }; device: "file" { path: "output.wav"; }; sample: "S16_LE"; channels: 2/0,1; dither: true; }; ## FILTERS ## filter "frfilter" { from_inputs: "fright"; to_outputs: "fr"; coeff: "dirac"; }; filter "flfilter" { from_inputs: "fleft"; to_outputs: "fl"; coeff: "dirac"; }; # End wavtest.conf EOF brutefir -nodefault wavtest.conf which gives: "Generating random numbers...Segmentation fault" .config can be found here: https://mega.nz/#!5wp3QL6T!JtJxHTm8_wR5RGrDsxTSkUT6CuQD-nW3iNxvEDDfva0 uname -a on qemu: Linux openadk 4.4.50-1 #1 Sun Mar 12 19:58:04 CET 2017 x86_64 GNU/Linux The same thing happend also on my asus_p5bvm machine on revision 0c6a3bd. On earlier revisions of adk (see oder e-mails) the rest ran fine. I don't really see where this might be coming from. Any ideas or insights are welcome! :-) Cheers Oliver P.S. The config file was modified slightly to avoid the /data path, so the the test can be run from anywhere, now.

3 4

[PATCH 15/15] Implement UBIFS rootfs support
by Phil Sutter 08 Mar '17

08 Mar '17

This implements UBIFS rootfs, enables it for mips targets and adds the necessary settings for rb532. Signed-off-by: Phil Sutter <phil(a)nwl.cc> --- mk/image.mk | 19 +++++++++++++++++++ mk/rootfs.mk | 1 + target/config/Config.in.rootfs | 9 +++++++++ target/linux/config/Config.in.flash | 23 ++++++++++++++++++++++- target/mips/Makefile | 8 ++++++++ 5 files changed, 59 insertions(+), 1 deletion(-) diff --git a/mk/image.mk b/mk/image.mk index 6b704f200938c..84d6ab9a80bd9 100644 --- a/mk/image.mk +++ b/mk/image.mk @@ -122,6 +122,7 @@ TARGET_KERNEL= ${ADK_TARGET_SYSTEM}-${ADK_TARGET_FS}-kernel INITRAMFS= ${ADK_TARGET_SYSTEM}-${ADK_TARGET_LIBC}-${ADK_TARGET_FS} ROOTFSSQUASHFS= ${ADK_TARGET_SYSTEM}-${ADK_TARGET_LIBC}-${ADK_TARGET_FS}.img ROOTFSJFFS2= ${ADK_TARGET_SYSTEM}-${ADK_TARGET_LIBC}-jffs2.img +ROOTFSUBIFS= ${ADK_TARGET_SYSTEM}-${ADK_TARGET_LIBC}-ubifs.img ROOTFSTARBALL= ${ADK_TARGET_SYSTEM}-${ADK_TARGET_LIBC}-${ADK_TARGET_FS}+kernel.tar.xz ROOTFSUSERTARBALL= ${ADK_TARGET_SYSTEM}-${ADK_TARGET_LIBC}-${ADK_TARGET_FS}.tar.xz ROOTFSISO= ${ADK_TARGET_SYSTEM}-${ADK_TARGET_LIBC}.iso @@ -191,6 +192,24 @@ ${FW_DIR}/${ROOTFSJFFS2}: ${TARGET_DIR} PATH='${HOST_PATH}' mkfs.jffs2 $(ADK_JFFS2_OPTS) -q -r ${TARGET_DIR} \ --pad=$(ADK_TARGET_MTD_SIZE) -o ${FW_DIR}/${ROOTFSJFFS2} $(MAKE_TRACE) +${FW_DIR}/${ROOTFSUBIFS}: ${TARGET_DIR} + ( \ + PATH='${HOST_PATH}'; \ + SP_SIZE='${ADK_TARGET_FLASH_SUBPAGE_SIZE}'; \ + PG_SZIE='${ADK_TARGET_FLASH_PAGE_SIZE}'; \ + LEB_SIZE=$$(((($$SP_SIZE + $$PG_SIZE) / $$PG_SIZE) * $$PG_SIZE)); \ + mkfs.ubifs -r ${TARGET_DIR} \ + -m $$PG_SIZE \ + -e $$((${ADK_TARGET_FLASH_PEB_SIZE} - $$LEB_SIZE)) \ + -c $$(((${ADK_TARGET_MTD_SIZE} / $$LEB_SIZE))) \ + -o ${FW_DIR}/rootfs.ubifs; \ + cd ${FW_DIR} && ubinize -o $@ \ + -p ${ADK_TARGET_FLASH_PEB_SIZE} \ + -m ${ADK_TARGET_FLASH_PAGE_SIZE} \ + -s ${ADK_TARGET_FLASH_SUBPAGE_SIZE} \ + "${ADK_TOPDIR}/target/${ADK_TARGET_ARCH}/${ADK_TARGET_SYSTEM}/ubinize.cfg"; \ + ) $(MAKE_TRACE) + createinitramfs: ${STAGING_TARGET_DIR}/${INITRAMFS}_list ${SED} 's/.*CONFIG_$RD_\|BLK_DEV_INITRD\|INITRAMFS_$.*//' \ ${LINUX_DIR}/.config diff --git a/mk/rootfs.mk b/mk/rootfs.mk index 027c671b6b492..15489603654a5 100644 --- a/mk/rootfs.mk +++ b/mk/rootfs.mk @@ -58,6 +58,7 @@ $(eval $(call rootfs_template,initramfspiggyback,INITRAMFSPIGGYBACK,rootfstype=t $(eval $(call rootfs_template,initramfsarchive,INITRAMFSARCHIVE,rootfstype=tmpfs)) $(eval $(call rootfs_template,squashfs,SQUASHFS,$(MTDDEV) rootfstype=squashfs)) $(eval $(call rootfs_template,yaffs,YAFFS,$(MTDDEV))) +$(eval $(call rootfs_template,ubifs,UBIFS,ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs)) $(eval $(call rootfs_template,jffs2,JFFS2,$(MTDDEV) rootfstype=jffs2)) $(eval $(call rootfs_template,nfsroot,NFSROOT,root=/dev/nfs ip=dhcp)) $(eval $(call rootfs_template,encrypted,ENCRYPTED)) diff --git a/target/config/Config.in.rootfs b/target/config/Config.in.rootfs index c24535f013617..335a4547f1303 100644 --- a/target/config/Config.in.rootfs +++ b/target/config/Config.in.rootfs @@ -87,6 +87,15 @@ config ADK_TARGET_ROOTFS_YAFFS help Root filesystem on NAND flash with YAFFS2. +config ADK_TARGET_ROOTFS_UBIFS + bool "UBIFS root filesystem (NAND)" + select ADK_KERNEL_UBIFS_FS + select ADK_HOST_NEED_MTD_UTILS + select ADK_HOST_NEED_KERNEL2MINOR + depends on ADK_TARGET_WITH_NAND + help + Root filesystem on NAND flash with UBI. + config ADK_TARGET_ROOTFS_NFSROOT bool "NFS root" select ADK_KERNEL_NETWORK_FILESYSTEMS diff --git a/target/linux/config/Config.in.flash b/target/linux/config/Config.in.flash index 3cf3a15ffa480..159e4aa45a520 100644 --- a/target/linux/config/Config.in.flash +++ b/target/linux/config/Config.in.flash @@ -163,9 +163,30 @@ config ADK_TARGET_MTD_SIZE int depends on ADK_TARGET_SYSTEM_QEMU_MICROBLAZE_S3ADSP1800 \ || ADK_TARGET_SYSTEM_QEMU_MICROBLAZE_ML605 \ - || ADK_TARGET_SYSTEM_QEMU_ARM_VEXPRESS_A9 + || ADK_TARGET_SYSTEM_QEMU_ARM_VEXPRESS_A9 \ + || ADK_TARGET_SYSTEM_MIKROTIK_RB532 default "16777216" if ADK_TARGET_SYSTEM_QEMU_MICROBLAZE_S3ADSP1800 default "33554432" if ADK_TARGET_SYSTEM_QEMU_MICROBLAZE_ML605 + default "134217728" if ADK_TARGET_SYSTEM_MIKROTIK_RB532 default "0" +config ADK_TARGET_FLASH_PEB_SIZE + int + default 131072 if ADK_TARGET_SYSTEM_MIKROTIK_RB532 + help + Physical Erase Block size. + +config ADK_TARGET_FLASH_PAGE_SIZE + int + default 2048 if ADK_TARGET_SYSTEM_MIKROTIK_RB532 + help + Minimum input/output size. + +config ADK_TARGET_FLASH_SUBPAGE_SIZE + int + default 512 if ADK_TARGET_SYSTEM_MIKROTIK_RB532 + default ADK_TARGET_FLASH_PAGE_SIZE + help + Size of NAND sub-pages (if supported). + endmenu diff --git a/target/mips/Makefile b/target/mips/Makefile index bb30049f15619..6f0bd728c27ec 100644 --- a/target/mips/Makefile +++ b/target/mips/Makefile @@ -87,6 +87,11 @@ else @echo 'sudo dd if=$(FW_DIR)/disk.img of=/dev/sdX bs=2048k' endif endif +ifeq ($(ADK_TARGET_FS),ubifs) +targethelp: + @echo 'The kernel file is: $(FW_DIR)/${TARGET_KERNEL}' + @echo 'The UBI image is: ${FW_DIR}/${ROOTFSUBIFS}' +endif # image creation and kernel install kernel-strip: @@ -121,3 +126,6 @@ endif ifeq ($(ADK_TARGET_FS),yaffs) imageinstall: $(FW_DIR)/$(ROOTFSTARBALL) targethelp endif +ifeq ($(ADK_TARGET_FS),ubifs) +imageinstall: $(FW_DIR)/$(ROOTFSUBIFS) targethelp +endif -- 2.9.3

2 1

[PATCH 14/15] target/config: Allow targets to require kernel2minor host package
by Phil Sutter 08 Mar '17

08 Mar '17

Signed-off-by: Phil Sutter <phil(a)nwl.cc> --- target/config/Config.in.tools | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/target/config/Config.in.tools b/target/config/Config.in.tools index adff5da9859be..46a73c5422b43 100644 --- a/target/config/Config.in.tools +++ b/target/config/Config.in.tools @@ -242,6 +242,15 @@ config ADK_HOST_BUILD_MTD_UTILS default y if ADK_HOST_NEED_MTD_UTILS default n +config ADK_HOST_NEED_KERNEL2MINOR + bool + default n + +config ADK_HOST_BUILD_KERNEL2MINOR + bool + default y if ADK_HOST_NEED_KERNEL2MINOR + default n + config ADK_HOST_BUILD_PATCHELF bool default n -- 2.9.3

1 0

[PATCH 13/15] Introduce kernel2minor package
by Phil Sutter 08 Mar '17

08 Mar '17

This is used to generate a yaffs2 filesystem image containing just the kernel binary as required by Mikrotik's rb532 board. Signed-off-by: Phil Sutter <phil(a)nwl.cc> --- package/kernel2minor/Makefile | 38 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 38 insertions(+) create mode 100644 package/kernel2minor/Makefile diff --git a/package/kernel2minor/Makefile b/package/kernel2minor/Makefile new file mode 100644 index 0000000000000..e7ace1d6151f2 --- /dev/null +++ b/package/kernel2minor/Makefile @@ -0,0 +1,38 @@ +# This file is part of the OpenADK project. OpenADK is copyrighted +# material, please see the LICENCE file in the top-level directory. + +include $(ADK_TOPDIR)/rules.mk + +PKG_NAME:= kernel2minor +PKG_VERSION:= 2cacb4dec6673a60a972a3a7f7629464a26a8492 +PKG_RELEASE:= 1 +PKG_GIT:= hash +PKG_DESCR:= kernel to Mikrotik NOR +PKG_SECTION:= sys/fs +PKG_URL:= https://github.com/adron-s/kernel2minor +PKG_SITES:= https://github.com/adron-s/kernel2minor.git + +include $(ADK_TOPDIR)/mk/host.mk +include $(ADK_TOPDIR)/mk/package.mk + +$(eval $(call HOST_template,KERNEL2MINOR,kernel2minor,$(PKG_VERSION)-$(PKG_RELEASE))) +$(eval $(call PKG_template,KERNEL2MINOR,kernel2minor,$(PKG_VERSION)-$(PKG_RELEASE),$(PKG_DEPENDS),$(PKG_DESCR),$(PKG_SECTION))) + +HOST_STYLE:= auto +HOST_CONFIG_STYLE:= manual +HOST_INSTALL_STYLE:= manual + +kernel2minor-hostinstall: + $(INSTALL_DIR) $(STAGING_HOST_DIR)/usr/sbin + $(INSTALL_BIN) $(WRKBUILD)/kernel2minor $(STAGING_HOST_DIR)/usr/sbin + +CONFIG_STYLE:= manual +INSTALL_STYLE:= manual + +kernel2minor-install: + $(INSTALL_DIR) $(IDIR_KERNEL2MINOR)/usr/sbin + $(INSTALL_BIN) $(WRKBUILD)/kernel2minor \ + $(IDIR_KERNEL2MINOR)/usr/sbin + +include ${ADK_TOPDIR}/mk/host-bottom.mk +include $(ADK_TOPDIR)/mk/pkg-bottom.mk -- 2.9.3

1 0

[PATCH 12/15] target/linux/config: Allow enabling UBIFS support
by Phil Sutter 08 Mar '17

08 Mar '17

Signed-off-by: Phil Sutter <phil(a)nwl.cc> --- target/linux/config/Config.in.fs | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/target/linux/config/Config.in.fs b/target/linux/config/Config.in.fs index 7c25754d1945c..b6226fc191c63 100644 --- a/target/linux/config/Config.in.fs +++ b/target/linux/config/Config.in.fs @@ -266,6 +266,20 @@ config ADK_KERNEL_YAFFS_FS help YAFFS2 filesystem for NAND devices +config ADK_KERNEL_MTD_UBI_GLUEBI + bool + +config ADK_KERNEL_MTD_UBI + tristate + select ADK_KERNEL_MTD + select ADK_KERNEL_MTD_UBI_GLUEBI + +config ADK_KERNEL_UBIFS_FS + tristate "UBIFS Filesystem" + select ADK_KERNEL_MTD_UBI + help + UBIFS is a file system for flash devices which works on top of UBI. + endmenu -- 2.9.3

1 0

[PATCH 11/15] package/mtd-utils: Enable UBIFS support in host build
by Phil Sutter 08 Mar '17

08 Mar '17

Signed-off-by: Phil Sutter <phil(a)nwl.cc> --- package/mtd-utils/Makefile | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) diff --git a/package/mtd-utils/Makefile b/package/mtd-utils/Makefile index ca8fac51f152a..cb5a69768f56d 100644 --- a/package/mtd-utils/Makefile +++ b/package/mtd-utils/Makefile @@ -11,7 +11,7 @@ PKG_DESCR:= flash filesystem utilities PKG_SECTION:= sys/fs PKG_DEPENDS:= libuuid liblzo PKG_BUILDDEP:= zlib util-linux liblzo -HOST_BUILDDEP:= liblzo-host +HOST_BUILDDEP:= liblzo-host zlib-host PKG_URL:= http://www.linux-mtd.infradead.org PKG_SITES:= ftp://ftp.infradead.org/pub/mtd-utils/ @@ -43,9 +43,10 @@ $(eval $(call PKG_template,FLASH_OTP_INFO,flash-otp-info,$(PKG_VERSION)-${PKG_RE $(eval $(call PKG_template,FLASH_OTP_DUMP,flash-otp-dump,$(PKG_VERSION)-${PKG_RELEASE},${PKG_DEPENDS},${PKGSD_FLASH_OTP_DUMP},${PKG_SECTION})) $(eval $(call PKG_template,FLASH_LOCK,flash-lock,$(PKG_VERSION)-${PKG_RELEASE},${PKG_DEPENDS},${PKGSD_FLASH_LOCK},${PKG_SECTION})) -HOST_STYLE:= manual +#HOST_STYLE:= manual +HOST_STYLE:= auto HOST_CPPFLAGS+= -DWITHOUT_XATTR=1 -I./include -HOST_MAKE_FLAGS+= WITHOUT_UBI=1 WITHOUT_LZO=1 +HOST_MAKE_FLAGS+= WITHOUT_LZO=1 host-build: (cd ${WRKBUILD} && env ${HOST_MAKE_ENV} ${MAKE} -f ${MAKE_FILE} \ @@ -53,15 +54,16 @@ host-build: mtd-utils-hostinstall: ${INSTALL_DIR} ${STAGING_HOST_DIR}/usr/bin - ${INSTALL_BIN} ${WRKBUILD}/mkfs.jffs2 \ + ${INSTALL_BIN} ${WRKBUILD}/mkfs.{jffs2,ubifs} \ ${STAGING_HOST_DIR}/usr/bin XAKE_FLAGS+= WITHOUT_XATTR=1 +ifneq (${ADK_PACKAGE_MTD_UTILS_WITH_UBIFS},y) +XAKE_FLAGS+= WITHOUT_UBI=1 +else ifneq (${ADK_PACKAGE_MTD_UTILS_WITH_LZO},y) XAKE_FLAGS+= WITHOUT_LZO=1 endif -ifneq (${ADK_PACKAGE_MTD_UTILS_WITH_UBIFS},y) -XAKE_FLAGS+= WITHOUT_UBI=1 endif XAKE_FLAGS+= BUILDDIR="${WRKDIST}" -- 2.9.3

1 0

[PATCH 10/15] package/zlib: Enable host-package
by Phil Sutter 08 Mar '17

08 Mar '17

Signed-off-by: Phil Sutter <phil(a)nwl.cc> --- package/zlib/Makefile | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/package/zlib/Makefile b/package/zlib/Makefile index 2da7e98bfb4d9..7f0c0ce1e4a79 100644 --- a/package/zlib/Makefile +++ b/package/zlib/Makefile @@ -13,10 +13,33 @@ PKG_URL:= http://www.zlib.net/ PKG_SITES:= http://zlib.net/ PKG_OPTS:= dev +include $(ADK_TOPDIR)/mk/host.mk include $(ADK_TOPDIR)/mk/package.mk +$(eval $(call HOST_template,ZLIB,zlib,$(PKG_VERSION)-$(PKG_RELEASE))) $(eval $(call PKG_template,ZLIB,zlib,$(PKG_VERSION)-$(PKG_RELEASE),$(PKG_DEPENDS),$(PKG_DESCR),$(PKG_SECTION),$(PKG_OPTS))) +HOST_STYLE:= auto +HOST_CONFIG_STYLE:= manual +HOST_CONFIGURE_ENV+= uname=Linux +HOST_ALL_TARGET:= libz.so.$(PKG_VERSION) + +host-configure: + (cd $(WRKBUILD); \ + uname="Linux" \ + $(HOST_CONFIGURE_OPTS) \ + CFLAGS="$(HOST_CFLAGS) -fPIC" \ + CPPFLAGS="-I$(STAGING_HOST_DIR)/usr/include" \ + LDFLAGS="-L$(STAGING_HOST_DIR)/usr/lib" \ + ./configure \ + --prefix=/usr \ + --shared \ + ); + +#zlib-hostinstall: +# $(INSTALL_DIR) $(STAGING_HOST_DIR)/usr/lib +# $(CP) $(WRKBUILD)/libz.so* $(STAGING_HOST_DIR)/usr/lib + CONFIG_STYLE:= manual CONFIGURE_ENV+= uname=Linux @@ -47,4 +70,5 @@ zlib-install: $(INSTALL_DIR) $(IDIR_ZLIB)/usr/lib $(CP) $(WRKINST)/usr/lib/libz.so* $(IDIR_ZLIB)/usr/lib +include ${ADK_TOPDIR}/mk/host-bottom.mk include $(ADK_TOPDIR)/mk/pkg-bottom.mk -- 2.9.3

1 0

[PATCH 09/15] mk/host-bottom: Introduce HOST_INSTALL_STYLE
by Phil Sutter 08 Mar '17

08 Mar '17

This is helpful when a package could use HOST_STYLE=auto but doesn't provide an install target. In that case, one can now set | HOST_STYLE=auto | HOST_CONFIG_STYLE=manual and define a custom host-install target while still making use of the auto targets for anything else. Signed-off-by: Phil Sutter <phil(a)nwl.cc> --- mk/host-bottom.mk | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/mk/host-bottom.mk b/mk/host-bottom.mk index 21a28a0511900..a8f6db773efc3 100644 --- a/mk/host-bottom.mk +++ b/mk/host-bottom.mk @@ -84,20 +84,22 @@ endif ${MAKE} host-build $(MAKE_TRACE) touch $@ +HOST_INSTALL_STYLE?= ${HOST_STYLE} + hostpost-install: host-install: ${ALL_HOSTINST} ${_HOST_FAKE_COOKIE}: ${_HOST_BUILD_COOKIE} @$(CMD_TRACE) "installing.. " @mkdir -p ${HOST_WRKINST} -ifeq (${HOST_STYLE},) +ifeq (${HOST_INSTALL_STYLE},) cd ${WRKBUILD} && env ${HOST_MAKE_ENV} ${MAKE} -f ${MAKE_FILE} \ DESTDIR='' ${HOST_FAKE_FLAGS} ${HOST_INSTALL_TARGET} $(MAKE_TRACE) endif -ifeq (${HOST_STYLE},auto) +ifeq (${HOST_INSTALL_STYLE},auto) cd ${WRKBUILD} && env ${HOST_MAKE_ENV} ${MAKE} -f ${MAKE_FILE} \ DESTDIR='${STAGING_HOST_DIR}' ${HOST_FAKE_FLAGS} ${HOST_INSTALL_TARGET} $(MAKE_TRACE) endif -ifeq (${HOST_STYLE},manual) +ifeq (${HOST_INSTALL_STYLE},manual) env ${HOST_MAKE_ENV} ${MAKE} host-install $(MAKE_TRACE) endif env ${HOST_MAKE_ENV} ${MAKE} hostpost-install $(MAKE_TRACE) -- 2.9.3

1 0

[PATCH 08/15] mk/host-bottom: Introduce HOST_CONFIG_STYLE
by Phil Sutter 08 Mar '17

08 Mar '17

This is helpful when a package could use HOST_STYLE=auto but doesn't ship a conforming configure script. In that case, one can now set | HOST_STYLE=auto | HOST_CONFIG_STYLE=manual and define a custom host-configure target while still making use of the auto targets for anything else. Signed-off-by: Phil Sutter <phil(a)nwl.cc> --- mk/host-bottom.mk | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/mk/host-bottom.mk b/mk/host-bottom.mk index 6fcd78e8846bd..21a28a0511900 100644 --- a/mk/host-bottom.mk +++ b/mk/host-bottom.mk @@ -3,6 +3,8 @@ host-extract: ${_HOST_PATCH_COOKIE} +HOST_CONFIG_STYLE?= ${HOST_STYLE} + hostpre-configure: host-configure: ${_HOST_CONFIGURE_COOKIE}: ${_HOST_PATCH_COOKIE} @@ -17,7 +19,7 @@ ifneq (,$(filter autoreconf,${AUTOTOOL_STYLE})) @touch ${WRKDIR}/.autoreconf_done endif @${MAKE} hostpre-configure $(MAKE_TRACE) -ifeq (${HOST_STYLE},) +ifeq (${HOST_CONFIG_STYLE},) @$(CMD_TRACE) "configuring.. " cd ${WRKBUILD}; \ env ${HOST_CONFIGURE_ENV} \ @@ -31,7 +33,7 @@ ifeq (${HOST_STYLE},) --sysconfdir=${STAGING_HOST_DIR}/etc \ ${HOST_CONFIGURE_ARGS} $(MAKE_TRACE) endif -ifeq (${HOST_STYLE},auto) +ifeq (${HOST_CONFIG_STYLE},auto) @$(CMD_TRACE) "configuring.. " cd ${WRKBUILD}; \ env ${HOST_CONFIGURE_ENV} \ @@ -51,13 +53,13 @@ ifeq (${HOST_STYLE},auto) --disable-nls \ ${HOST_CONFIGURE_ARGS} $(MAKE_TRACE) endif -ifeq (${HOST_STYLE},cmake) +ifeq (${HOST_CONFIG_STYLE},cmake) @$(CMD_TRACE) "configuring cmake.. " cd ${WRKBUILD}; PATH='${HOST_PATH}' \ cmake -Wno-dev -DCMAKE_INSTALL_PREFIX:PATH=/usr \ ${HOST_CMAKE_FLAGS} ${WRKSRC} $(MAKE_TRACE) endif -ifeq (${HOST_STYLE},perl) +ifeq (${HOST_CONFIG_STYLE},perl) @$(CMD_TRACE) "configuring perl module.. " cd ${WRKBUILD}; \ PATH='${HOST_PATH}' \ @@ -66,7 +68,7 @@ ifeq (${HOST_STYLE},perl) $(HOST_PERL_ENV) \ perl-host Makefile.PL ${HOST_CONFIGURE_ARGS} endif -ifeq (${HOST_STYLE},manual) +ifeq (${HOST_CONFIG_STYLE},manual) @$(CMD_TRACE) "configuring.. " ${MAKE} host-configure $(MAKE_TRACE) endif -- 2.9.3

1 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

dev March 2017